Visit the SWFA.com site to check out our current specials. |
308 case issues |
Post Reply | Page 12> |
Author | |
Wolf2
Optics GrassHopper Joined: July/12/2013 Status: Offline Points: 18 |
Post Options
Thanks(0)
Posted: January/06/2017 at 18:30 |
Hello my fellow reloaders, I started reloading for a new Savage 12FV in 308 (Cabela's exclusive) and have been having a heck of a time. I have two problems. 1. I have been having trouble finding a load. Components: LC'16 Once fired brass, IMR-4064, 178gr AMAX, WLR primer. I have tested loads multiple times. From 41-44.5 grains. The new brass would not chamber in my rifle at all as it was fired out of 7.62 rifles. So I kept bumping the shoulder back until there was no resistance when closing the bolt. I do not have a headspace gauge. Load development at 100 yards was normal. 42gr of IMR 4064 at 2.800" was giving .5"-.8" groups on multiple occasions. But when I backed out to the 200yds and 265yds the groups were huge (2 MOA). So the muzzle velocity must not be consistent. I have played with seating depth but my chambers max COAL is 2.817" 2. Last time I shot the cases started showing case head separation at the 4th firing. Only 1 case had a extremely visible slit around it with a few others showing a shiny line. It appears that I am bumping back the shoulder a little too much. Should I size the brass so there is some resistance when closing the bolt? I know lake city brass is not the best brass but its all I have. Maybe the 2 problems are linked Next I am going to try different brass (R-P) and probably the 168 Hornady HPBT. I have some pictures but not sure how to post them. I will try to get them up. I know reloaders love problems so please give me some advice. |
|
anweis
Optics Master Joined: January/29/2006 Status: Offline Points: 1148 |
Post Options
Thanks(0)
|
I don't shoot a .308, but i used LC .308 brass to make my .338 Federal cases. I read your post carefully, i have a few comments based on my own experiences reloading for 11 rifle calibers.
1. If your rifle shoots slightly less than 1" groups at 100 and 2" groups at 200 and further, the load is very good. The groups are not "huge", they are normal and as expected. At 200 yards, the slightest shooter error in technique and slight wind would account for your expecting 1.5" groups and achieving just slightly larger groups. Also, ambient conditions and barrel condition may have been different. 2. You cannot assume that your loads have inconsistent velocities based on group size at 200 yards. You need to use a good chronograph, preferably one that gives good readings regardless of weather or ambient light. 3. 4064 is a good powder for .308, but with that brass, bullet, and rifle, other powders may shoot better. I usually try 3 powders and 3-4 bullets before i make up my mind about a rifle. 4. It does sound like you are doing something wrong with the brass. You may need to squeeze the body in a small base die or a tighter full size die, rather than bumping the shoulders so much. Better yet, with a good rifle, trying to achieve best target grade accuracy, buy a lot of Lapua (the best), Nosler, or Starline brass. Starline sells very good brass, 250 cases for a bit over $100. Between a full body die and a neck die, a good lot of brass will last 12-20 firings and give better results. I cringe when i think where that LC brass may have been, or how it was used. It may come from different lots, could have been fired in different sized chambers at different pressures, etc. Not conducive to longevity and best accuracy.
|
|
anweis
Optics Master Joined: January/29/2006 Status: Offline Points: 1148 |
Post Options
Thanks(0)
|
Oh, how many kinds of primers have you tried? I have several loads where switching primers turned 1" groups into one hole groups, if i shot properly. Shot over a chronograph, i could not tell much difference in velocity or consistency.
|
|
jonoMT
Optics Master Extraordinaire Joined: November/13/2008 Location: Montana Status: Offline Points: 4853 |
Post Options
Thanks(0)
|
I had bad luck with some LC brass and realized it there was no way to know how many times it had been fired (since I bought it through an estate sale). Buy new brass (Lapua is fantastic). Every .308 I've ever loaded for, bolt or semi-auto, has thrived on Varget, CCI BR primers and 168-175 gr. bullets. I never load past 2.81". With proper, safe load development Varget can be taken up to mildly compressed loads. But you've got to watch for the signs relative to your rifle. You already know that, I realize...just can't say it often enough for those new to handloading.
|
|
Reaction time is a factor...
|
|
Wolf2
Optics GrassHopper Joined: July/12/2013 Status: Offline Points: 18 |
Post Options
Thanks(0)
|
At first I used Winchester Large Rifle, then the last outing I used Seller & Bellot primers ($25/K)!!! Reviews said the S&B's gave lower SDs in muzzle velocity. But I didn't really see a difference in accuracy. Load data research showed that people were getting great result with IMR-4064 around 42-43.5. I did try Varget and got weird groups at 100 yards. I loaded up 5 rounds of 43.5, 44, 44.5 as this is were most find the accuracy node. 43.5 shot 3 round in .25" (cloverleaf) the next 2 opened up to 1" 44 did the same thing, 3 into .25" and the next 2 opened to 1.2". Then 44.5 same story. I have about bullets left to test Varget at 200 yards see what happens. I may be expecting a little too much out of the savage. I also reload for my AR15 and the cases last 8-10 reloads. (Privi and Remington) I know I need a chronograph and lapua brass but I am strapped as a 18 year old. Also how do you guys go about bump sizing? |
|
anweis
Optics Master Joined: January/29/2006 Status: Offline Points: 1148 |
Post Options
Thanks(0)
|
on your bolt action, distance between bullet ogive and rifling also makes a difference. I noticed that sometimes a 0.010" difference can turn the load from good to outstanding. Loaded COL or OAL makes a difference. 1'-1.5" on a benched load is just fine for that. I bump shoulders or squeeze the lower portion of the body on brass depending on situation. I use either full body die or neck die adjusted up or down accordingly. I have both types of dies for each caliber. It pays off on the long run, because i buy the best brass available and i can make it last longer.
|
|
Wolf2
Optics GrassHopper Joined: July/12/2013 Status: Offline Points: 18 |
Post Options
Thanks(0)
|
I will do some more load development with different components. I will also try sizing it less as savages tend to have very tight chambers. I love field shooting. I am lucky to have a wheat field near my house were I can shoot to about 470yrds with my AR. I recently read a article on precision rifle blog that talks about how group size is really not a big a factor as you think. http://precisionrifleblog.com/2015/04/15/how-much-does-group-size-matter/
|
|
When in doubt, C4
|
|
Steelbenz
Optics Jedi Knight ROLL TIDE ROLL Joined: January/03/2006 Location: Heart of Dixie Status: Offline Points: 5153 |
Post Options
Thanks(0)
|
With that bullet you might want to try some 2000-MR also!
|
|
"Don't argue with a fool! From a distance you can't really tell who's who!"
|
|
Wolf2
Optics GrassHopper Joined: July/12/2013 Status: Offline Points: 18 |
Post Options
Thanks(0)
|
I loaded 15 rounds with Varget with 3 different charges in Remington brass. 43.5, 44, 44.5 All of which did much better. 44 and 44.5 were about equivalent. At 211 yards both showed vertical dispersion of 1.5". Drop was around 2-4 inches with 4" being lowest. On JBM this put me around 2725fps (26" barrel). Midway has some 178gr Seconds for a good price that are worth a look. I will definitely check out that powder.
|
|
When in doubt, C4
|
|
BeltFed
Optics Retard Joined: February/12/2008 Location: Ky Status: Offline Points: 22287 |
Post Options
Thanks(0)
|
Lake City 7.62x51 brass is military brass with thicker case walls and heads, so it doesn't have the same dimensions as commercial brass, and will generate higher pressures than commercial brass with the same load. It also has crimped primers, but that's another issue. If you're getting brass that came from a military source, then it was fired in a machine gun, that have huge chambers compared to commercial rifles, and they are very hard on brass, especially in the firing, extraction and ejection process. 3 firings is about normal for this brass, as the first time it went through that MG, it took a lot of life out of the brass.
Military brass should be used for practice/blasting ammo, as you are never going to get any decent accuracy out of it. I tried using 7.62NATO brass that I fired out of a M1A, to come up with practice load for a Savage FP10 to shoot steel plates at 500yds.. I tried bullets, powder, primers, and tweaking the cases, and nothing was going to get to 500yds with any reliability. I finally switched to new Winchester .308 brass, and my groups shrunk dramatically. I finally got my groups down to 1 or 2 hole 5 shot groups at 100yds. |
|
Life's concerns should be about the 120lb pack your trying to get to the top of the mountain, and not the rock in your boot.
|
|
budperm
Optics Retard show me your sheep!! Joined: January/01/2009 Location: Pennsylvania Status: Offline Points: 31710 |
Post Options
Thanks(0)
|
Yep for .308 I use Varget with CCI LR primers... 16" barrel might be a TAD SHORT FOR OPTIMAL BURN...
|
|
"Peace is that brief glorious moment in history when everybody stands around reloading".
--Thomas Jefferson |
|
Urimaginaryfrnd
MODERATOR Resident Redneck Joined: June/20/2005 Location: Iowa Status: Offline Points: 14964 |
Post Options
Thanks(0)
|
I tend to use Varger or IMR 4350 and while I do load some 168 I prefer to shoot 190 and 200 gr bullets. Better brass would be a good choice.
|
|
"Always do the right thing, just because it is the right thing to do". Bobby Paul Doherty Texas Ranger |
|
3_tens
Optics Jedi Master Joined: January/08/2007 Location: Oklahoma Status: Offline Points: 7853 |
Post Options
Thanks(0)
|
H4350 would be a good powder if your using a 16" barrel.
|
|
Folks ain't got a sense of humor no more. They don't laugh they just get sore.
Need to follow the rules. Just hard to determine which set of rules to follow Now the rules have changed again. |
|
nralifer
Optics Apprentice Joined: July/26/2016 Status: Offline Points: 165 |
Post Options
Thanks(0)
|
I shoot the 308 a lot, and have tried many brands of brass. The brass that has given me the most consistent results is the Lapua Palma brass with the small rifle primer. Extreme spreads in velocity of around 10-15 fps, and some times 5 fps. The brass is not that cheap, but you get what you pay for.
|
|
It is hard to fail, but it is worse never to have tried to succeed. TR
|
|
billyburl2
Optics Master Extraordinaire Joined: January/08/2009 Location: Cottonwood, AZ Status: Offline Points: 4015 |
Post Options
Thanks(0)
|
I get that with my son's 308,using cheap zq Turkish brass. |
|
If it is tourist season, why can't we shoot them?
|
|
BeltFed
Optics Retard Joined: February/12/2008 Location: Ky Status: Offline Points: 22287 |
Post Options
Thanks(0)
|
I get good results using new Winchester brass. Yeah it's not machined brass like Lapua, but it can be worked up to give me really good results, and I can have a lot more brass for the same cost of Lapua, and get a lot of firings out of the cases too. I think of unfired, unprimed Winchester cases as the poor man's Lapua brass that needs a little work.
|
|
Life's concerns should be about the 120lb pack your trying to get to the top of the mountain, and not the rock in your boot.
|
|
Wolf2
Optics GrassHopper Joined: July/12/2013 Status: Offline Points: 18 |
Post Options
Thanks(0)
|
I have about 20 cases of Remington 308 brass that I am working with right now. Capital Cartridge had Winchester Headstamp 308 brass for $14/100 which is great(last week). But they are out right now. But they still have some R-P. Would you say that Winchester is superior to Remington?
|
|
When in doubt, C4
|
|
JLud
Optics Journeyman Joined: January/30/2010 Location: Bettendorf, Iow Status: Offline Points: 670 |
Post Options
Thanks(0)
|
Buy some gold medal match in bullet weights to compare some factory loads as well. I like to measure off of as well, plus good brass when done.
|
|
That thing on the left....my old ride, some days I miss her.
|
|
BeltFed
Optics Retard Joined: February/12/2008 Location: Ky Status: Offline Points: 22287 |
Post Options
Thanks(0)
|
Probably not a nickles worth of difference. In the past, I didn't get as good results with Remington as I did with Winchester, but that was a long time ago. |
|
Life's concerns should be about the 120lb pack your trying to get to the top of the mountain, and not the rock in your boot.
|
|
Lockjaw
Optics Journeyman Joined: May/17/2016 Location: Chelsea Status: Offline Points: 434 |
Post Options
Thanks(0)
|
I'm gonna load some with cfe223 once hunting season is over.
|
|
Post Reply | Page 12> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |