Visit the SWFA.com site to check out our current specials. |
Criterion 6.5 creedmoor barrel issues |
Post Reply | Page 123> |
Author | |
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
Posted: June/07/2017 at 12:10 |
So I bought a 6.5 creed AR 10 barrel. 18" model.
Got it last week, and installed it. I noted the threaded end of the barrel was very long. I have a 6.5 Thunderbeast ultra 7 that uses a compact brake or flash suppressor to attach to. So I bough an new flash suppressor for it and went to screw it on. Turns out the flash suppressor is only threaded a .65 inches deep. The barrel is threaded .73 deep to the shoulder. The flash suppressor came with a shim kit but it still does not give it enough length to do it fit. So I tried a crush washer which gave it the length, but that canted the muzzle device enough that when I looked down the barrel I could see the edge of my baffles in my Ultra 7. Initally I was not sure if this was a threading issues or the crush washer. So I email Criterion about how long it is and worried that it might be out of spec. They email me back saying it is highly unlikely that their barrel could be out of spec. So I grab a bunch of my other 5/8x24 barrels and start to measure. Not one of them measured longer than .620 inches. I have seven other threaded barrels both factory and custom done by a gun smith. So I now call them and talk to the same guy that emailed me about it. I told him I have two different thunder beast 5/8x24 muzzle devices and neither one of them will thread all the way on. He then tells me that Thunder beast is known for making them really short. I said well I have 7 other threaded barrels and they thread on to all of those and I had measured them and none of them measure over .62 inches. He said yeah that is normal for ar 15 type barrels but on larger caliber the standard is .73. I said well I think you guys are out of the norm as 4 of the barrels I measured are not ar-15 barrels but bolt action barrels. And the other 3 are 6.8 spc and 300 blk barrels that are 5/5x24 threaded. He just said that's weird cause ours are the normal size. Anyway, just seems weird to me that they would make them so much longer than anyone else. I really don't want to put shims in it as the look like crap and will cause a big bulge where they are larger than the barrel and muzzle brake. Looking at the muzzle device, it looks like I could thread it a little deeper and get it to the shoulder. Going to run it to a machine shop later today and see what they think. Edited by supertool73 - June/07/2017 at 13:34 |
|
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
|
Rancid Coolaid
MODERATOR Joined: January/19/2005 Location: United States Status: Offline Points: 9318 |
Post Options
Thanks(0)
|
thunderbeast is well known for exceedingly well made cans and threads, very precisely cut.
If there is a problem, I would bet money it isn't a thunderbeast issue. A machine shop can cut it down to work, but they shouldn't have to. Good data point, sorry for the troubles, thanks for sharing. |
|
Freedom is something you take.
Respect is something you earn. Equality is something you whine about not being given. |
|
SEMO Shooter
Optics Apprentice Joined: January/06/2013 Location: SE Missouri Status: Offline Points: 199 |
Post Options
Thanks(0)
|
I have a pdf from Silencerco that shows 1/2x28 or 5/8x24 muzzle thread depth to be .600 +or- .010
https://s3.amazonaws.com/com.silencerco/support/thread-specs/rifle_thread_specs.PDF
|
|
SEMO Shooter
Optics Apprentice Joined: January/06/2013 Location: SE Missouri Status: Offline Points: 199 |
Post Options
Thanks(0)
|
Thunderbeast thread specs
https://thunderbeastarms.com/tech/thread-specifications
|
|
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
I took a bunch of pics so you can really see how far off they are making them. I just don't understand why they are doing this.
Even the thread protector will not fit over the threads all the way. I think they just have a problem that they need to fix. But they got the attitude that their barrels can't be wrong. My 30 cal thunder beast 30p-1 is a thread on and it will work, but not the muzzle devices. Criterion barrel 6.5 creedmoor Mossberg MVP .308 barrel Obermyer .308 m40 barrel cut by Bugholes.com Tikka CTR 6.5 creed barrel Ruger 300 blk barrel Seekins precision 300 blk barrel Rainier Arms match 300 blk barrel. |
|
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
|
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
I do want to add that the dude at Criterion was super nice and tried to help, but all the helps were just bandaids to the problem that the threading is to long and out of the norm. Really if I want it fixed right I am going to have to pay to the the barrel cut off and repaired or maybe get the muzzle brake threads lengthened.
I am going to try the muzzle brake, just hope it doesn't get ruined as they cost $125. |
|
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
|
Rancid Coolaid
MODERATOR Joined: January/19/2005 Location: United States Status: Offline Points: 9318 |
Post Options
Thanks(0)
|
Is it mounted?
Were it me, I'd send it back if possible. Do not use a crush washer, do not do anything that increases risk of baffle strike! |
|
Freedom is something you take.
Respect is something you earn. Equality is something you whine about not being given. |
|
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
Yes, it is installed and has fired 5 shots, for function purposes. I got the muzzle device several days after, I never thought it would be an issue.
With the crush washer it would definitely get a baffle strike. It made it very canted. |
|
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
|
koshkin
MODERATOR Dark Lord of Optics Joined: June/15/2004 Location: United States Status: Offline Points: 13181 |
Post Options
Thanks(0)
|
If the crush washer could get it that canted, is the thread itself out of spec, aside from the threading length? It sounds like it is pretty loose.
ILya
|
|
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
Unless they are butted up against the shoulder anything will wobble pretty bad. I can partially thread my 30P-1 on all of my barrels and until it is against the shoulder you can wobble it a bit. So I dare bet the crush washer just crushed more on one side than the other.
The guy at Criterion told me crush washers are fine for flash suppressors, but for something that you need to be perfectly aligned the should not be used. I kind of figured that would be the case, but I was hoping it would work. You can tell pretty easily if a suppressor is not aligned correctly just by looking into the chamber end of the barrel with it attached. |
|
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
|
Rancid Coolaid
MODERATOR Joined: January/19/2005 Location: United States Status: Offline Points: 9318 |
Post Options
Thanks(0)
|
If your 30P wobbles before shouldering, I'd stop everything. That is not right, not good!
|
|
Freedom is something you take.
Respect is something you earn. Equality is something you whine about not being given. |
|
koshkin
MODERATOR Dark Lord of Optics Joined: June/15/2004 Location: United States Status: Offline Points: 13181 |
Post Options
Thanks(0)
|
The threads on your barrel are likely it if spec (this Ted's field, so you should probably check with him).
If you've got the suppressor threaded on by 0.6" and it is that loose, I'd be concerned. ILya |
|
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
Lets not jump to a bunch of conclusions about all my stuff being out of spec based upon my few words on a computer screen. I am not talking about wobbling like crazy. I guess I worded that bad. All threads have a slight bit of movement until they are tight against something. The more thread you get into the suppressor the less wobble you get. Obviously some are better than others. The threads cannot be completely tight or you could not thread things onto them. That is why they put a shoulder on them so they have something to get square and tight against.
I have been using my 30p-1 for years and works just fine on multiple hosts. I always visually inspect before I shoot a can for the first time. And occasionally after. My 30p-1 threads onto the Criterion barrel just as good as it does onto my Greg Young threaded barrel, and my Seekins, and Tikka etc. |
|
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
|
koshkin
MODERATOR Dark Lord of Optics Joined: June/15/2004 Location: United States Status: Offline Points: 13181 |
Post Options
Thanks(0)
|
Alright. That's fair. There is always some slight looseness and, admittedly, my experience with suppressors is zilch (thank you, California!).
My only experience with precision threads is with optical assemblies and they are pretty tight even when they are not contacting a shoulder ILya
|
|
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
I wonder if the optical threads feel tighter because they are not cut near as deep. I would assume the deeper the cut the more strength is offered. But I no very little about it myself.
One part of all those pics I find interesting is the difference of the relief cut near the shoulder. Some of them are huge, others almost zilch. The Tikka has almost no relief cut, wonder if they are done on a CNC machine where the others are done on a lathe. I have read that those relief cuts can affect accuracy and reputability. Guess we will wait for Ted to clarify that as well. After re reading my last post. I think I wrote badly again. I apologize, I often write quickly without a proof read. When I said all threads have a slight bit of movement. I should have put all my threads, meaning the barrels I have with my suppressor. My info about a shoulder I got direct from Thunderbeast as I called them about threading a really thin barrel for my 30p-1. But they said it was two small and without a substantial shoulder it could not get tight and square. |
|
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
|
Rancid Coolaid
MODERATOR Joined: January/19/2005 Location: United States Status: Offline Points: 9318 |
Post Options
Thanks(0)
|
Wobble a few threads in is bad. If it wobbles when near the shoulder, that is exceedingly not good.
I have several cans and many threaded barrels. If you get 5+ turns in and still have wobble, I'd call that either bad threads on the barrel or bad threads on the can. Or both. |
|
Freedom is something you take.
Respect is something you earn. Equality is something you whine about not being given. |
|
RifleDude
MODERATOR EVIL OPPRESSOR Joined: October/13/2006 Location: Texas Status: Offline Points: 16337 |
Post Options
Thanks(0)
|
Your Criterion barrel's thread length is too long. It's possible they intended it to be used for flash hider only and therefore intended to be used with a washer. Usually flash hiders have enough clearance between the flash hider i.d. and the bore diameter that a tiny bit of non-concentricity isn't an issue and a crush washer can be used no problem. But this also depends on the thread's class of fit. A suppressor is another story, however, since it is longer and any angular misalignment is amplified over greater length. It needs a precision locating feature.
All 60-deg UN threads have some clearance between the pin and box threads built in to the thread tolerance or they will gall and seize up. The degree of "slop" between the internal and external thread depends on the class of fit. Most likely, they cut the thread to a Class 2A/2B fit. Class 3A/3B is a slightly tighter fit and wouldn't show any visible axial movement when being mated together. In my opinion, these threads really should be class 3 for best function. Threads are NOT precision location features; they are fastening features only and should not be relied upon to keep your muzzle device concentric to the bore. A thread cannot ensure concentricity unless it is a tapered, locking thread and even then, threads are almost never used for precision location/alignment. This is why it is essential a suppressor locates against a shoulder, a tight cylindrical mating surface, or even better, a conical shoulder. Finally, it's not difficult at all to shorten the barrel thread. Just take it to a competent machine shop and have them set back the muzzle by .1", re-face and crown the muzzle. However, you shouldn't have to do this; Criterion should fix it for you. Do not increase the internal thread depth of your flash hider or suppressor. That's more difficult to do properly because you have to pick up the thread lead, and only increases the gap between the end of your muzzle and the i.d. shoulder of your muzzle device when used on barrels with .6" thread length. So if your only option was to increase the internal thread depth, it would be best to increase the thread relief at the rear of the thread to a shoulder rather than try to chase the thread lead. Loose items on the end of barrels are dangerous. Don't play around with it until it's right.
|
|
Ted
Money can't buy happiness... but it's much more comfortable to cry in a Porsche than on a bicycle. |
|
RifleDude
MODERATOR EVIL OPPRESSOR Joined: October/13/2006 Location: Texas Status: Offline Points: 16337 |
Post Options
Thanks(0)
|
The answer is BOTH. They are cut on CNC lathes. Thread reliefs are essential against shoulders so that the threaded component can fully mate against a shoulder. The function of a thread relief is to allow the thread on the mating component to continue past the end of the thread on the connection with the relief. A thread relief also removes the last partial imperfect thread "feather edge" so the threaded connection doesn't bind.
|
|
Ted
Money can't buy happiness... but it's much more comfortable to cry in a Porsche than on a bicycle. |
|
supertool73
Optics God Superstool Joined: January/03/2008 Status: Offline Points: 11814 |
Post Options
Thanks(0)
|
Thanks Ted. I will call criterion tomorrow and see if they will shorten it. But i dare bet based on conversation i had today i will be paying someone to do it. Just glad i bought a stainless one and not one of their nitrade finished ones.
|
|
Lifetime warranty and excellent customer service don't mean a thing when your gun fails during a zombie attack.
"A Liberal is a person who will give away everything they don't own." |
|
Rancid Coolaid
MODERATOR Joined: January/19/2005 Location: United States Status: Offline Points: 9318 |
Post Options
Thanks(0)
|
Criterion barrels: noted.
Never. Ever. Ever. Ever. |
|
Freedom is something you take.
Respect is something you earn. Equality is something you whine about not being given. |
|
Post Reply | Page 123> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |